How to use the shower for a few more years?

For office workers after a busy day, going home and taking a bath is definitely a great pleasure in life. When the dense and soft water flows on the body, the tired body can finally enjoy the joy. How can this wonderful feeling be described as refreshing? But the reality may sometimes be: the shower has only been bought not long ago, and I don`t know why the water flow is small when the water is small, and the comfortable shower often becomes annoying.

What are the reasons for the low water output from the shower?

There are external factors and internal factors that affect the water output of the shower.

External factors such as the water pressure in your community, the greater the water pressure, the greater the water output; whether the installation steps of the shower are correct and whether it is properly maintained. Because there are a lot of impurities in the newly-decorated pipes, and even a lot of fine sand, if the shower is installed directly to drain the water, these impurities may directly enter the interior of the shower, which is not easy to clean, and affects the water output effect of the shower; On the one hand, it may be caused by the internal reasons of the water heater.

Internal factors such as the internal design of the shower. If the internal waterway of the shower is designed to be relatively small, or the water outlet is relatively small, the effect of the water will be poor. So be careful when buying.

How to find the specific cause of the small water output?

1. Turn on the faucet to see how the water is coming out. If the faucet at home has a lot of water, it means that the water pressure is sufficient.

2. Unscrew the place where the shower hose is connected to the water heater, and try the other joints connected to the water pipe. If the shower has a small amount of water, it means that the shower is blocked. Clean the shower. If the shower is normal, it means that the problem is not in the shower, it may be on the water heater.

3. Check the water heater. The design of the internal pipe of the gas water heater is conducive to heating. At the same time, this design will also hinder the flow of water to a certain extent and reduce the water pressure.

4. Check carefully whether the installation steps are correct. Improper installation, deformed rubber ring, uneven or too thin outlet pipe joint, mismatch between hose and shower, etc.

5. Check the water quality at home. We can use the kettles and pots and other tools to heat the water. If a layer of white scale will appear for a period of time, it means that the water quality of your home will easily block the shower holes. ; In addition, air deposits and dust will also enter the interior through the small holes of the shower, and long-term accumulation will also block the

shower; improper adjustment of the shower nozzle may also cause the increase of foreign matter and scale.

We can solve the problem of small water output for different reasons.

1. Regardless of the low water pressure caused by the community itself or the design of the water heater, it is recommended to connect a booster pump in series to the main switch of the water supply valve to increase the water output of the shower.

2. The pipeline valve connected to the water heater is opened smaller, and the water inlet valve is opened larger.

3. The water mixing valve is congenital inadequate and the diameter is small, and the throttling causes the water output to become smaller. The inlet end of the detachable water mixing valve can be connected to the water heater's water supply valve with a hose, or the nozzle hose can be directly connected to the water heater. Try the hot water outlet end, and distinguish the quality of the mixing valve according to the water output of the nozzle; replace the mixing valve of the formal brand under the premise that the water pressure of the water source is satisfied.

4. Improper installation, deformed rubber ring, uneven or too thin outlet pipe joint, mismatch between hose and shower, etc.: Select the appropriate hose and shower according to the specifications, replace the rubber ring, and reinstall. Before installation, it is best to put the water in the pipe and flush the pipe to prevent impurities from entering the pipe, causing the sprinkler's water outlet to be blocked.

5. The sprinklers are congenital inadequate, and the internal resistance is large, resulting in small water output. Replace the self-cleaning shower sprinklers in time. Normally, just gently gently clean with your hands.

6. The shower pipe is easy to be entangled together, and the pipe is blocked and cannot produce water: protect the water pipe during use, and choose anti-winding water pipes to ensure smooth water flow in the water pipe.

7. Water quality problem at home: We can rotate and adjust the shower nozzle; after disassembling the nozzle, put the nozzle upward, and find a soft object to gently touch it to shake off the clogged gravel, and use it at the same time. Clean the spray holes one by one, and then repeatedly clean them with clean water, and then install and restore.